Audi Cabriolet


Audi A4  Driveshaft

Audi A4 Driveshaft

Driveshaft Audi A4,Audi Cabriolet,Audi A6 2005 > Special tools and workshop equipment required Alignhment Fixture-4W Dr.Shaft 3139 Pry Lever - Rmv Outside Mirror 80 - 200 Counterhold tool Touareg V10 T10172 and Adapters T10172/5 Engine/Transmission Jack V.A.G 1383 A with Universal Transmission Support V.A.G 1359/2 Removing See notes, refer to Go to article “ Driveshaft Overview ” Audi A4,Audi Cabriolet,Audi A6 2005 > Working on the driveshaft sho..

Audi A4  Flange Shaft Seals

Audi A4 Flange Shaft Seals

Flange Shaft Seals Audi A4,Audi Cabriolet Special tools and workshop equipment required Seal Installer - Driveshaft Flange 2062 Drip Tray VAG1306 Torque Wrench 1331 5-50Nm VAG1331 Torque Wrench 1332 40-200Nm VAG1332 Engine/Transmission Jack V.A.G 1383 A with Universal Transmission Support V.A.G 1359/2 Wheel Hub Support T10149 Sealing grease G 052 128 A1 Removing The rear final drive is installed Follow the general repair instructions, refer to..

Audi A4  Rear Final Drive

Audi A4 Rear Final Drive

Rear Final Drive Audi A4,Audi Cabriolet,Audi A6 2005 > Special tools and workshop equipment required Torque Wrench 1332 40-200Nm VAG1332 Engine/Transmission Jack V.A.G 1383 A with Universal Transmission Support V.A.G 1359/2 RemovingObserve general repair notes, refer to Go to article “ General Repair Information ” Audi A4,Audi Cabriolet,Audi A6 2005 > . Remove rear section of exhaust system from clamping sleeves arrows . Refer to Engine Mechanical Rep. Gr. 26 D..

Audi A4 (AMB) Camshaft Adjustment Valve 1, Checking

Audi A4 (AMB) Camshaft Adjustment Valve 1, Checking

Camshaft Adjustment Valve 1, Checking Audi A4,Audi Cabriolet Special tools and workshop equipment required Multimeter . Wiring diagram. Test requirements The Camshaft Adjustment Valve 1 N205 fuse OK. Motronic Engine Control Module (ECM) Power Supply Relay J271 OK, checking Wiring diagrams, Troubleshooting & Component locations . Battery voltage at least 12.5 volts. All electrical consumers such as, lights and rear window defroster, switched off. Vehicles with automatic ..

Audi A4 (AMB) Camshaft Position Sensor, Checking

Audi A4 (AMB) Camshaft Position Sensor, Checking

Camshaft liition Sensor, Checking Audi A4,Audi Cabriolet Note Use only gold-plated terminals when servicing terminals in harness connector of Camshaft liition (CMP) Sensor G40 . Special tools and workshop equipment required Multimeter . Wiring diagram. Test requirements The Motronic Engine Control Module (ECM) J220 fuses OK. Battery voltage at least 12.5 volts. All electrical consumers such as, lights and rear window defroster, switched off. Vehicles with automatic tran..

Audi A4 (AMB) Can-Bus Terminal Resistance, Checking

Audi A4 (AMB) Can-Bus Terminal Resistance, Checking

Can-Bus Terminal Resistance, Checking Audi A4,Audi Cabriolet Special tools and workshop equipment required Multimeter . Wiring diagram. Test requirement A CAN-Bus malfunction was recognized. The Motronic Engine Control Module (ECM) J220 fuses OK. Battery voltage at least 12.5 volts. All electrical consumers such as, lights and rear window defroster, switched off. Vehicles with automatic transmission, shift selector lever into liition “P” or “N”. A/C switched off. Ground (GND)..

Audi A4 (AMB) Charge Air Pressure Sensor, Checking

Audi A4 (AMB) Charge Air Pressure Sensor, Checking

Charge Air Pressure Sensor, Checking Audi A4,Audi Cabriolet Note Use only gold-plated terminals when servicing terminals in harness connector of Charge Air Pressure Sensor G31 . Special tools and workshop equipment required Multimeter . Wiring diagram. Test requirements The Motronic Engine Control Module (ECM) J220 fuses OK. Battery voltage at least 12.5 volts. All electrical consumers such as, lights and rear window defroster, switched off. On vehicles with automatic ..

Audi A4 (AMB) Clean Working Conditions

Audi A4 (AMB) Clean Working Conditions

Clean Working Conditions Audi A4,Audi Cabriolet Even minor contaminations can lead to malfunctions in the fuel injection system. When working on the fuel supply/injection system, pay careful attention to the following rules for cleanliness: Thoroughly clean all unions and adjacent areas with engine or brake cleaner and dry before disconnecting. Plug open lines and connections immediately with appropriate protective caps. Place removed parts on a clean surface and cover. Use lint-free cloth..

Audi A4 (AMB) Clean Working Conditions

Audi A4 (AMB) Clean Working Conditions

Clean Working Conditions Audi A4,Audi Cabriolet When working on turbocharger, carefully observe the following Clean Working Conditions: Thoroughly clean all connections and the surrounding area before disconnecting. Place parts that have been removed on a clean surface and cover. Use lint-free cloths only! Carefully cover over opened components or seal, if repairs are not carried out immediately. Only install clean components: Only unpack replacement parts immediately prior to installatio..

Audi A4 (AMB) Clean Working Conditions

Audi A4 (AMB) Clean Working Conditions

Clean Working Conditions Audi A4,Audi Cabriolet When working on the fuel supply/injection system, pay careful attention to the following Clean Working Conditions: Thoroughly clean all connections and the surrounding area before disconnecting. Place parts that have been removed on a clean surface and cover them. Do not use fluffy cloths! Carefully cover over opened components or seal, if repairs are not performed immediately. Only install clean components: Only unpack replacement parts imm..




Showing 1 to 10 of 458 (46 Pages)