Audi A4 - (1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002)


Audi A4  Removal and Installation

Audi A4 Removal and Installation

Removal and Installation Audi A4 ALL Go to article “ A/C Compressor, Replace ” Audi A4 Go to article “ A/C Compressor ” Audi A4 Go to article “ Compressor Refrigerant Lines, ” Audi A4 Go to article “ A/C Compressor Bracket, 4-Cylinder ” Audi A4 Go to article “ A/C Compressor Bracket, 6-Cylinder with Zexel Compressor ” Audi A4 Go to article “ A/C Compressor Bracket, 6-Cylinder with Nippondenso Compressor ” Audi A4 Go to article “ A/C Clutch, Z..

Audi A4  Reverse Drive Gear, Removing and installing

Audi A4 Reverse Drive Gear, Removing and installing

Reverse Drive Gear, Removing and installing Audi A4 Locking Ring Support plate Reverse Drive Gear Different variations, allocation, refer to Fig. Needle Bearing Thrust Washer Transmission cover with axle for the reverse drive gear arrow It is not necessary to remove the reverse drive gear axle in order to remove the reverse drive gear Reverse drive gear axle is not available as a replacement part TORX bolt 35 Nm Serves as an additional axle mount for the reverse drive gear..

Audi A4 (ACK,AGA,AJG,ALF,ALG,AML,AMM,AMX,APR,APS,APZ,AQD,ARJ,ATX,AHA,ATQ) Camshaft Adjustment Solenoid Valves, Checking

Audi A4 (ACK,AGA,AJG,ALF,ALG,AML,AMM,AMX,APR,APS,APZ,AQD,ARJ,ATX,AHA,ATQ) Camshaft Adjustment Solenoid Valves, Checking

Camshaft Adjustment Solenoid Valves, Checking Audi A4 Special tools and workshop equipment required Analog/Digital Multimeter VAG1526A or FLU83III Voltage Tester VAG1527B Connector Test Set VAG1594C or VAG1594A Adapter VAG1598/22 (vehicles with accelerator cable) Adapter cable VAG1598/31 (vehicles with Electronic throttle) Vehicle Diagnostic Tester with Diagnostic Cable VAS5051/1 The adjustment of intake camshaft is load- and RPM dependent. Oil pres..

Audi A4 (ACK,AGA,AJG,ALF,ALG,AML,AMM,AMX,APR,APS,APZ,AQD,ARJ,ATX,AHA,ATQ) Description and Operation

Audi A4 (ACK,AGA,AJG,ALF,ALG,AML,AMM,AMX,APR,APS,APZ,AQD,ARJ,ATX,AHA,ATQ) Description and Operation

Description and Operation Audi A4 Go to article “ Power Steering Pump Ribbed Belt Drive, Generator, Viscous Fan and A/C System Component Overview ” Audi A4 Go to article “ Toothed Belt Drive Component Overview ” Audi A4 Go to article “ Sealing Flange and Dual Mass Flywheel/Drive Plate Component Overview ” Audi A4 Go to article “ Crankshaft Component Overview ” Audi A4 Go to article “ Sawed Connecting Rods Component Overview ” Audi A4 Go to article “ ..

Audi A4 (AEB) Barometric Pressure Sensor, Checking

Audi A4 (AEB) Barometric Pressure Sensor, Checking

Barometric Pressure Sensor, Checking Audi A4 Special tools and workshop equipment required Multimeter . Wiring diagram. Test requirements Fuse S229 OK. The ignition switched off. Test procedure Perform a preliminary check to verify the customers complaint. Refer to Go to article . Start diagnosis Remove the engine cover. Checking voltage Disconnect the Barometric Pressure (BARO) Sensor F96 electrical harness connector. Switch the ignition on. Using a multimeter , check th..

Audi A4 (AEB) Camshaft Position Sensor, Checking

Audi A4 (AEB) Camshaft Position Sensor, Checking

Camshaft liition Sensor, Checking Audi A4 Note Use only gold-plated terminals when servicing terminals in harness connector of Camshaft liition (CMP) Sensor G40 . Special tools and workshop equipment required Multimeter . Wiring diagram. Test requirements The Motronic Engine Control Module (ECM) J220 fuses OK. Battery voltage at least 12.5 volts. All electrical consumers such as, lights and rear window defroster, switched off. Vehicles with automatic transmission, shift ..

Audi A4 (AEB) CAN Data Link

Audi A4 (AEB) CAN Data Link

CAN Data Link Audi A4 ”CAN” is an acronym for Controller Area Network.The ECM communicates with all databus capable control modules by a CAN Data Link.The databus capable control modules (i.e. Engine Coolant temperature Sensor) are connected by two data bus wires which are twisted together (CAN_High and CAN_Low), and exchange information (messages) to the ECM. Missing information on the databus is then recognized and stored as a malfunction.The ECM illuminates the MIL through the CAN data li..

Audi A4 (AEB) Clean Working Conditions

Audi A4 (AEB) Clean Working Conditions

Clean Working Conditions Audi A4 When working on the fuel supply/injection system, pay careful attention to the following rules of cleanliness: Thoroughly clean all connections and the surrounding area before disconnecting. Place parts that have been removed on a clean surface and cover them. Do not use fluffy cloths! Carefully cover over opened components or seal, if repairs are not performed immediately. Only install clean components: Only unpack replacement parts immediately prior to i..

Audi A4 (AEB) Clean Working Conditions

Audi A4 (AEB) Clean Working Conditions

Clean Working Conditions Audi A4 When working on turbocharger, carefully observe the following Rules of Cleanliness: Thoroughly clean all connections and the surrounding area before disconnecting. Place parts that have been removed on a clean surface and cover. Use lint-free cloths only! Carefully cover over opened components or seal, if repairs are not carried out immediately. Only install clean components: Only unpack replacement parts immediately prior to installation. Do not use parts..

Audi A4 (AEB) Clean Working Conditions

Audi A4 (AEB) Clean Working Conditions

Clean Working Conditions Audi A4 When working on turbocharger, carefully observe the following Rules of Cleanliness: Thoroughly clean all connections and the surrounding area before disconnecting. Place parts that have been removed on a clean surface and cover. Use lint-free cloths only! Carefully cover over opened components or seal, if repairs are not carried out immediately. Only install clean components: Only unpack replacement parts immediately prior to installation. Do not use parts..




Showing 1 to 10 of 438 (44 Pages)