Audi A5 Cabriolet


Audi A5  Control Arm Ball Bearing, Replacing

Audi A5 Control Arm Ball Bearing, Replacing

Control Arm Ball Bearing, Replacing Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Pressing out and in bearing for track control arm (on wheel bearing housing side) Special tools and workshop equipment required Press Plate VW402 Press Piece - Multiple Use VW412 Subframe Bushing Tool Kit 3301 Bearing Installer - Control Arm 3346 Hydraulic Press - Bushing Tool Kit T10030 Assembly Paste Note Hold track control arm firmly in liition while pressing bearing ou..

Audi A5  Control Arm, Removing and Installing

Audi A5 Control Arm, Removing and Installing

Control Arm, Removing and Installing Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Special tools and workshop equipment required Engine and Gearbox Jack VAS6931 Puller - Ball Joint T40010A Torque Wrench 1332 Insert - Ring Wrench - 18mm VAG1332/10 or Torque Wrench 1332 Insert - Ring Wrench - 21mm VAG1332/7 Removing Remove the wheel. Remove the noise insulation. Refer to Body Exterior Rep. Gr. 66 Noise Insulation; Overview - Noise Insulation . In vehicles wit..

Audi A5  Control Arm, Tie Rod

Audi A5 Control Arm, Tie Rod

Control Arm, Tie Rod Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ Overview - Transverse Link ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ Upper Transverse Link, Removing and Installing ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ Lower Transverse Link, Removing and Installing ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ Tie Rod, Removing and Installing ” Audi A5,Audi A5 Cabriol..

Audi A5  Control Position, Programming

Audi A5 Control Position, Programming

Control liition, Programming Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Special tools and workshop equipment required Vehicle Diagnostic Tester WARNING During a test drive, the testing and measuring equipment must always be secured on the back seat. These devices may be operated only by a passenger during a test drive. Connect the Vehicle Diagnostic Tester Switch on the Vehicle Diagnostic Tester . The Vehicle Diagnostic Tester is ready for operation when the operating mod..

Audi A5  Coupling Rod, Removing and Installing

Audi A5 Coupling Rod, Removing and Installing

Coupling Rod, Removing and Installing Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Special tools and workshop equipment required Torque Wrench 1332 40-200Nm VAG1332 Note As a running change in MY 2010, aluminum coupling rods were replaced by plastic coupling rods. Do not use different coupling rods on one axle; allocation refer to the Parts Catalog. Removing A5 through August 2007 Disconnect connections 1 and 2 . Remove the coupling rod 3 . A4/A5 from September 2007 D..

Audi A5  CV Joint, Servicing

Audi A5 CV Joint, Servicing

CV Joint, Servicing Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Outer CV Joint, Removing Clamp the drive axle with protective jaws in a vise clamp. Open both clamping sleeves and remove protective joint boot from outer joint. Strike a copper or brass drift A on CV joint inner race with a hammer. Remove joint and protective joint boot. Outer CV Joint, Installing Joints and protective joint boots must be free of grease. Replace the circlip 1 . Slide on the small clamp with the p..

Audi A5  Damaged Threads in Longitudinal Member, Repairing (Subframe to Body)

Audi A5 Damaged Threads in Longitudinal Member, Repairing (Subframe to Body)

Damaged Threads in Longitudinal Member, Repairing (Subframe to Body) Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Damaged threads can be repaired using wire inserts (Helicoil®). Have the thread repair checked by the responsible foreman or next person in charge. Thread insert must be same length as thread in body. Repair any damage to the underbody sealant. Refer to General Information; Body Repairs, Body Collision Repair . ..

Audi A5  Diagonal Brace, Removing and Installing

Audi A5 Diagonal Brace, Removing and Installing

Diagonal Brace, Removing and Installing Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Special tools and workshop equipment required Torque Wrench 1332 40-200Nm VAG1332 Removing Place the vehicle on a hoist. Remove the rear noise insulation 2 . Refer to Body Exterior Rep. Gr. 66 Noise Insulation; Overview - Noise Insulation . Remove the bolts 1 and 2 and the diagonal brace. InstallingInstallation is the reverse of removal, with special attention to the following: No..

Audi A5  Diagonal Brace, Removing and Installing (A5 Cabriolet)

Audi A5 Diagonal Brace, Removing and Installing (A5 Cabriolet)

Diagonal Brace, Removing and Installing (A5 Cabriolet) Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ Diagonal Brace, Removing and Installing, A5 Cabriolet, Front Wheel Drive (FWD) ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ Diagonal Brace, Removing and Installing, A5 Cabriolet, All Wheel Drive (AWD) ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > ..

Audi A5  Diagonal Brace, Removing and Installing, A5 Cabriolet, All Wheel Drive (AWD)

Audi A5 Diagonal Brace, Removing and Installing, A5 Cabriolet, All Wheel Drive (AWD)

Diagonal Brace, Removing and Installing, A5 Cabriolet, All Wheel Drive (AWD) Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Special tools and workshop equipment required Torque Wrench 1332 40-200Nm VAG1332 Removing Place the vehicle on a hoist. Remove the covers 1 and 2 . Refer to Body Exterior Rep. Gr. 66 Underbody Trim Panel; Overview - Underbody Panels . Remove the left and right bolts arrows and remove the diagonal braces. Remove the left 1 bolt first and the..




Showing 31 to 40 of 1778 (178 Pages)