Audi A5 Cabriolet


Audi A5  Explanation of Production Control Numbers (PR Number), Audi A4

Audi A5 Explanation of Production Control Numbers (PR Number), Audi A4

Explanation of Production Control Numbers (PR Number), Audi A4 Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > The vehicle data plate documents which front/rear axle or tire pressure monitoring system is installed using the corresponding PR numbers.There is a vehicle data label in the spare wheel well and also one in the customer Maintenance booklet.Front/Rear Axle The front/rear axle PR No. is in illustration A and B . The front axle PR number is item A . Item B shows the PR num..

Audi A5  Fresh Air Intake, Removing and Installing

Audi A5 Fresh Air Intake, Removing and Installing

Fresh Air Intake, Removing and Installing Audi A5,Audi Q5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 >,Audi 80 2-tuerig Rl Note Depending on the version, for some countries with high dust levels (for example China), a dust filter C is installed in the filter mount B instead of the intake grille A . The dust filter C prevents pollen and sand from getting sucked into the Fresh Air Blower V2 . Refer to the Parts Catalog. Make sure when removing the dust filter C that dirt do..

Audi A5  Front Axle

Audi A5 Front Axle

Front Axle Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ Overview - Front Axle ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > ..

Audi A5  Front Axle Camber, Adjusting

Audi A5 Front Axle Camber, Adjusting

Front Axle Camber, Adjusting Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Special tools and workshop equipment required Torque Wrench 1332 40-200Nm VAG1332 Torque Wrench 1410 VAG1410 Commercially Available Plastic-Coated Tire Iron Camber cannot be adjusted.Camber can be centered evenly within specified tolerance range by shifting subframe. Remove the noise insulation. Refer to Body Exterior Rep. Gr. 66 Noise Insulation; Overview - Noise Insulation . Loosen the thread..

Audi A5  Front Axle Toe, Adjusting

Audi A5 Front Axle Toe, Adjusting

Front Axle Toe, Adjusting Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Measure the dimension a between the tie rod head 1 and the left and right tie rod 2 and make note of the value. The dimension a should be the same before and after adjusting on the left and right. Loosen lock nut B . Note Counterhold the tie rod end C when loosening the lock nut B . Adjust toe on left and right–hand wheels at hex A . Be sure that boot is not twisted after turning the tie ..

Audi A5  Front Passenger Side Footwell Vent, Removing and Installing

Audi A5 Front Passenger Side Footwell Vent, Removing and Installing

Front Passenger Side Footwell Vent, Removing and Installing Audi A5,Audi Q5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 >,Audi 80 2-tuerig Rl Note From 01/2008, A/C units which have an additional connection for the glove compartment cooling are being installed. Refer to Go to article “ Glove Compartment Cooling Connection on Air Intake Housing ” Audi A5,Audi Q5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 >,Audi 80 2-tuerig Rl . Make sure that the correct right radiator housing and air intak..

Audi A5  Front Shock Absorbers, Venting and Emptying

Audi A5 Front Shock Absorbers, Venting and Emptying

Front Shock Absorbers, Venting and Emptying Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Special tools and workshop equipment required Pipe Cutter, Commercially Available A - Venting through Drill Holes Secure gas-filled shock absorber vertically in vise, with piston rod facing down. WARNING Wear protective eyewear while drilling. Drill a 3 mm hole arrow A through the shock absorber outer tube. Note Gas escapes when drilling. Continue drilling until the tube inside is drilled..

Audi A5  General Information

Audi A5 General Information

General Information Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > (Edition 02.2014) Go to article “ Tire Pressure Monitoring System General Information ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ Tire Pressure Monitoring System (TPMS) General Information ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ Dynamic Steering General Information ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ Drive Axle General ..

Audi A5  General Information

Audi A5 General Information

General Information Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ General Information, Front Axle ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ General Information, Rear Axle ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > Go to article “ General Information, Steering ” Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > ..

Audi A5  General Information, Front Axle

Audi A5 General Information, Front Axle

General Information, Front Axle Audi A5,Audi A5 Cabriolet,Audi A5,Audi A4 2008 > When installing waxed components, contact surfaces must be cleaned. Contact surfaces must be free of wax and grease.Tightening specifications for non-lubricated bolts and nuts are given.Always replace self-locking nuts and bolts.Always replace the bolts and nuts, which are tightened with an additional tightening angle.Welding or straightening operations are not permitted on load-bearing or wheel-controlling comp..




Showing 81 to 90 of 1778 (178 Pages)